海信led55ec680us 不能开机，附串口 日志。-液晶电视
資深大佬 : cqcw 8
海信led55ec680us遥控板开机后 指示灯 红变蓝 5秒后变红，不能开机。
整个过程屏幕黑屏，无声音，，，按esc键停留在fastboot# 2秒就关机了。不能命令行输入命令。
麻烦各位大神看看。谢谢。
日志不能直接贴。。在附件 zip文件里。
Bootrom start
Boot Media: eMMC
Decrypt auxiliary code …OK
Auxiliary area start!
Auxiliary code – v1.00
DDR code – V1.2.1 20160503
Build: Jul 15 2017 – 22:18:24
Reg Version: v134
Reg Time: 2016/9/8 18:53:39
Reg Name: hi3751v620_4layer_cpu1000_DDR1600_2048m_1024mch0_1024mch1_emmc.reg
DDRTR Suc
Enable gpio19-4
Auxiliary area end!
Starting…
System startup
Fastboot 3.3.0 (gfkfcmo@ubuntu-CI-2) (Jul 15 2017 – 22:18:28)
Fastboot: Version 3.3.0
Build Date: Jul 15 2017, 22:19:03
CPU: Hi3751v620
Boot Media: eMMC
MMC: Synopsys Mobile storage: 0
MMC/SD Card:
MID: 0x000090
OID: 0x014a
PSN: 0x57d55e1c
DATA: 06/2017
Name: "HAG4a2"
Chip Type: MMC
Version: UNKNOWN
Timing: HS
Host Clk: 50000000Hz
Host Div: 0
Bus Width: 8bit
Chip Size: 15758000128 Bytes (High Capacity)
Read Block: 512 Bytes
Write Block: 512 Bytes
Boot Addr: 0
The DDR memory layout:
page table: 0x0c000000 – 0x0c400000 4 MiB
stack: 0x0c400000 – 0x0c800000 4 MiB
global data: 0x0cbfffc4 – 0x0cc00000 60 Bytes
malloc: 0x0cc00000 – 0x10c00000 64 MiB
.text: 0x10c00000 – 0x10cae238 696.6 KiB
data: 0x10cae238 – 0x10e620c0 1.7 MiB
DISP_HAL_Get_PanelCfgPara SyncInfo: Hact=3840 Hfb=200 Hbb=360 Vact=2160 Vfb=30 Vbb=60
DISP_HAL_Get_PanelCfgPara SyncInfo: Hact=3840 Hfb=200 Hbb=360 Vact=2160 Vfb=30 Vbb=60
Vb1 u32Clk=891000000, u32IntPart=0x1002094, u32MinorPart=0x12800000
HPLL Lock Success u32Tmp=9
HPLL Lock Success u32Tmp=1
vbo_para_cksel=0x2, vbo_div_cksel=0x3 vo_hd_tv_cksel=2 lvds_cken=1, vbo_div_cken=0, vbo_para_cken=0, vbo_para_phy_pctrl=0
u32PixelClk=594000000, HpllTargetClk=891000000,u32HpllCtrl0=0x12800000, u32HpllCtrl1=0x1002094
Set Disp 1 SyncInfo: V (30, 60, 2160) H (200, 360, 3840)
SrInCscEnable=1 , SrOutCscEnable=1, SrInColor=12, SrOutColor=12
enSrPosition =1 stSrZmePara In wh[1920 1080] Out wh[3840 2160] ZME_FMT =2
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
SDK_VERSION: [HiDPTAndroidV300R001C01SPC023_20160909]
Set CEC onetouchplay :0
BootMode = POWER OFF
get bootloader message reserved:
BootMode = 1 ACDC = 1
will_enter_recovery = 0
boot_after_reboot = 0
Read FactoryM = 0
Go to sleep
System suspend.
======== [MCU PARAM] ========
SYSID: 0x19050600
DBGMASK: 0x00000001
SUSPENDTYPE: 0x00000000
GPIO POWER KEY: 0x00000000
GPIO LEVEL: 0x00000000
TIMER WAKEUP: 0xFFFFFFFF
IRTYPE: 0x00000004
IR NUM: 0x00000004
IR KEY: 0xF20DBF00
IR KEY: 0xF30C0E0E
IR KEY: 0xED120E0E
IR KEY: 0xEC130E0E
LSADC ZERO: 0x000000FC
LSADC channel A enable
LSADC channel B enable
LSADC GLITCHSAMPLE: 0x00000005
LSADC TIMESCAN: 0x00000258
LSADC POWERKEY0: 0x00000000, 0x000000EC
LSADC POWERKEY1: 0x000000FF, 0x000000FF
LSADC POWERKEY2: 0x000000FF, 0x000000FF
LSADC POWERKEY3: 0x000000FF, 0x000000FF
UART Wakeup Key: 0x000000FF
Auto wakeup flag: 0x00000000
Light off
CEC ONE Play:0x00000000
HDMIRX HPD invert:0x00000006
HDMIRX HPD function:0x00000000
HDMIRX bCecWkup:0x00000000
lsadc:6bit,data_delta=8,enable deglitch,power down,continue scan
======== [MCU Init Ready] ========
Power down ARM ===>
Set MCU to 24MHz ===>
Config bus core idle state ===>
Test bus core state ===>
DDR_PowerCtrl:1010001
group 0,bit 1 have no pinmux
======== [ARM Power Down] ========
Wait for 2s …
======== [Waiting for Powerkey] ========
整个过程屏幕黑屏，无声音，，，按esc键停留在fastboot# 2秒就关机了。不能命令行输入命令。
麻烦各位大神看看。谢谢。
日志不能直接贴。。在附件 zip文件里。
Bootrom start
Boot Media: eMMC
Decrypt auxiliary code …OK
Auxiliary area start!
Auxiliary code – v1.00
DDR code – V1.2.1 20160503
Build: Jul 15 2017 – 22:18:24
Reg Version: v134
Reg Time: 2016/9/8 18:53:39
Reg Name: hi3751v620_4layer_cpu1000_DDR1600_2048m_1024mch0_1024mch1_emmc.reg
DDRTR Suc
Enable gpio19-4
Auxiliary area end!
Starting…
System startup
Fastboot 3.3.0 (gfkfcmo@ubuntu-CI-2) (Jul 15 2017 – 22:18:28)
Fastboot: Version 3.3.0
Build Date: Jul 15 2017, 22:19:03
CPU: Hi3751v620
Boot Media: eMMC
MMC: Synopsys Mobile storage: 0
MMC/SD Card:
MID: 0x000090
OID: 0x014a
PSN: 0x57d55e1c
DATA: 06/2017
Name: "HAG4a2"
Chip Type: MMC
Version: UNKNOWN
Timing: HS
Host Clk: 50000000Hz
Host Div: 0
Bus Width: 8bit
Chip Size: 15758000128 Bytes (High Capacity)
Read Block: 512 Bytes
Write Block: 512 Bytes
Boot Addr: 0
The DDR memory layout:
page table: 0x0c000000 – 0x0c400000 4 MiB
stack: 0x0c400000 – 0x0c800000 4 MiB
global data: 0x0cbfffc4 – 0x0cc00000 60 Bytes
malloc: 0x0cc00000 – 0x10c00000 64 MiB
.text: 0x10c00000 – 0x10cae238 696.6 KiB
data: 0x10cae238 – 0x10e620c0 1.7 MiB
DISP_HAL_Get_PanelCfgPara SyncInfo: Hact=3840 Hfb=200 Hbb=360 Vact=2160 Vfb=30 Vbb=60
DISP_HAL_Get_PanelCfgPara SyncInfo: Hact=3840 Hfb=200 Hbb=360 Vact=2160 Vfb=30 Vbb=60
Vb1 u32Clk=891000000, u32IntPart=0x1002094, u32MinorPart=0x12800000
HPLL Lock Success u32Tmp=9
HPLL Lock Success u32Tmp=1
vbo_para_cksel=0x2, vbo_div_cksel=0x3 vo_hd_tv_cksel=2 lvds_cken=1, vbo_div_cken=0, vbo_para_cken=0, vbo_para_phy_pctrl=0
u32PixelClk=594000000, HpllTargetClk=891000000,u32HpllCtrl0=0x12800000, u32HpllCtrl1=0x1002094
Set Disp 1 SyncInfo: V (30, 60, 2160) H (200, 360, 3840)
SrInCscEnable=1 , SrOutCscEnable=1, SrInColor=12, SrOutColor=12
enSrPosition =1 stSrZmePara In wh[1920 1080] Out wh[3840 2160] ZME_FMT =2
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
SDK_VERSION: [HiDPTAndroidV300R001C01SPC023_20160909]
Set CEC onetouchplay :0
BootMode = POWER OFF
get bootloader message reserved:
BootMode = 1 ACDC = 1
will_enter_recovery = 0
boot_after_reboot = 0
Read FactoryM = 0
Go to sleep
System suspend.
======== [MCU PARAM] ========
SYSID: 0x19050600
DBGMASK: 0x00000001
SUSPENDTYPE: 0x00000000
GPIO POWER KEY: 0x00000000
GPIO LEVEL: 0x00000000
TIMER WAKEUP: 0xFFFFFFFF
IRTYPE: 0x00000004
IR NUM: 0x00000004
IR KEY: 0xF20DBF00
IR KEY: 0xF30C0E0E
IR KEY: 0xED120E0E
IR KEY: 0xEC130E0E
LSADC ZERO: 0x000000FC
LSADC channel A enable
LSADC channel B enable
LSADC GLITCHSAMPLE: 0x00000005
LSADC TIMESCAN: 0x00000258
LSADC POWERKEY0: 0x00000000, 0x000000EC
LSADC POWERKEY1: 0x000000FF, 0x000000FF
LSADC POWERKEY2: 0x000000FF, 0x000000FF
LSADC POWERKEY3: 0x000000FF, 0x000000FF
UART Wakeup Key: 0x000000FF
Auto wakeup flag: 0x00000000
Light off
CEC ONE Play:0x00000000
HDMIRX HPD invert:0x00000006
HDMIRX HPD function:0x00000000
HDMIRX bCecWkup:0x00000000
lsadc:6bit,data_delta=8,enable deglitch,power down,continue scan
======== [MCU Init Ready] ========
Power down ARM ===>
Set MCU to 24MHz ===>
Config bus core idle state ===>
Test bus core state ===>
DDR_PowerCtrl:1010001
group 0,bit 1 have no pinmux
======== [ARM Power Down] ========
Wait for 2s …
======== [Waiting for Powerkey] ========
本主题由 gf2133 于 7 天前 审核通过
大佬有話說 (0)